A little gadget that sits on your water or electricity meter and monitors it continuously. The collected reading are presented on a mobile web page so that you can practice saving ressources by answering questions like "How much water do I use when I take a shower?".

Currently Sensus water meters are supported. They look like this:

I have designed two versions of a PCB which fits on top of the water meter which uses GP2S700HCP reflective photointerrupter sensors to read the turning of the half shiny half red disc. The disc makes one turn per liter. The PCB has six optical sensors, so it can sense quantities around 1/12 of a liter. The reflective part of the disc is not exactly a half circle, so the exact 12 quantities measured are different from each other. An automatic calibration method is provided which determines how much each quantity is. You can print a [PDF rendering of the PCB layout](pcb/Optical water meter reader/optical meter reader board.pdf), make 5mm holes for the steering pins plus a small hole for the middle of the sensor circle in your printout and see if it will fit on your meter. When attached to your meter the small hole should be right above the center of the disc.

• The top row shows the version of the PCB designed to run on two 1.5V batteries and transmit the readings wirelessly.
  • [Eagle schematics](pcb/Optical water meter reader/optical meter reader v3.sch) / [PDF schematics](pcb/Optical water meter reader/optical meter reader v3 battery assembly.pdf)
  • [Eagle board file](pcb/Optical water meter reader/optical meter reader v3.brd)
  • [Gerber files](pcb/Optical water meter reader/optical meter reader v3 - gerber.zip)
  • [Bill of materials](pcb/Optical water meter reader/optical meter reader v3 battery assembly BOM.txt)
  • Firmware
• The bottom row shows the version of the PCB designed to be connected directly to a PC using a USB cable. In the configuration shown here it operates as the radio receiver that receives the readings transmitted from other units.
  • [Eagle schematics](pcb/Optical water meter reader/optical meter reader.sch) / [PDF schematics](pcb/Optical water meter reader/optical meter reader.pdf)
  • [Eagle board file](pcb/Optical water meter reader/optical meter reader.brd)
  • [Gerber files](pcb/Optical water meter reader/optical meter reader gerber.zip)
  • Firmware

The ambition is that the same or a similar PCB will be able to read the turning weel on an old style electricity meter. The PCB was designed in Eagle pcb and the schematics are available [here](pcb/Optical water meter reader/optical meter reader.pdf).

The USB version uses an Arduino Nano as the CPU module and NRF24L01+ Wireless Transceiver Module for wireless connectivity. The battery powered module has the microcontroller directly on the PCB.

The server application runs on a PC written in Go and stores the measurements in a Postgres database. The server application exposes a REST API, a socket.io service for real time updates and also serves a web application written in React.

The communication protocol between the embedded code and the server is based on Google's protocol buffers with the Arduino implementation generated by Nanopb. The protocol definition file is MeterReader.proto.

All build instructions assume Ubuntu 15.04 or later.

sudo apt-get install make clang protobuf-compiler arduino postgresql-9.4 git
wget https://godeb.s3.amazonaws.com/godeb-amd64.tar.gz
tar xzf godeb-amd64.tar.gz
./godeb install

The project uses git submodules, so you have to use a recursive clone to get everything:

git clone --recursive https://github.com/martinhansdk/Continuous-Meter-Reader

Using an AVR ISP programmer (for instance an Arduino with the ArduinoISP sketch loaded), attach it to the ISP header on the meter reader board. In the Arduino IDE select the appropriate programmer type. Choose the board type to be "Arduino Pro or Pro Mini (3.3V, 8 MHz) w/ ATmega328". Then run "Tools > Burn bootloader".

Once this has completed correctly, the brown out detection must be cleared in the AVR in order to allow operating the AVR at 2.5V. Do this by running:

avrdude -patmega328p -cstk500v1 -P /dev/ttyUSB? -b19200 -U efuse:w:0xff:m

Now disconnect the ISP and connect a 3.3V FTDI USB to serial adapter to JP2. The run

cd src/Continuous-Meter-Reader
make upload

Attach the Arduino for the server receiver station and run

cd src/RadioStation
make upload

cd go
export GOPATH=$PWD
go get -d
go build MeterServer.go 
go build ConfigNode.go 
go build SampleSender.go 

Drop step 1 if you already have a database running

1. change postgres default password: su - postgres psql \password postgres
2. Create the 'meter' user: CREATE USER meter;
3. Set user password: \password meter;
4. Create the database: CREATE DATABASE meter;
5. Grant priviledges to meter on database: GRANT ALL PRIVILEGES ON DATABASE meter TO meter;
6. Grant priviledges to meter on the database tables: GRANT ALL PRIVILEGES ON TABLE meters TO meter; GRANT ALL PRIVILEGES ON TABLE measurements TO meter;
7. Create the database fields by executing the commands in database.sql
8. Insert the first meter into the meter table: INSERT INTO meters( id, name, unit, current_series, last_count, scale) VALUES (1, 'Mock meter', "L", "0", "0", 1e-3), (10, "Water", "L", "0", "0", 1e-3);

Each node has an id which is an integer between 1 and 127. We need to set this id and also choose the wireless or serial (USB) protocol. Configuration can only happen over USB.

To configure an Arduino that is attached to /dev/ttyUSB0 run something like the following:

go/ConfigNode -serial=/dev/ttyUSB0 -wirelessproto -id=10 -uncalibrate

The calibration procedure is as follows:

1. Attach the PCB to the water meter
2. Connect the Arduino to the PC using a USB cable
3. Turn on a tap so that a constant flow is running. Make sure this is the only place water is consumed in the house while the calibration is running
4. Run the command go/ConfigNode -serial=/dev/ttyUSB0 -calibrate
5. The command will exit when calibration is complete

Once the database is set up, and the MeterServer built, it can be run:

cd go ./MeterServer

Contact the server using http://localhost:2111/static

Running tests with out having to flush a lot of water makes sense, so use the

cd go ./SampleSender

for this purpose.

If everything is ok, the example output should look something like this:

2015/11/10 22:25:00 Waiting for current settings
2015/11/10 22:25:00 Connection established
2015/11/10 22:25:00 Waiting for data
2015/11/10 22:25:02 len= 14
2015/11/10 22:25:02 n=14
2015/11/10 22:25:02 NOTE : Received 'Rebooted'
2015/11/10 22:25:02 Waiting for data
2015/11/10 22:25:02 len= 24
2015/11/10 22:25:02 n=24
2015/11/10 22:25:02 Waiting for data
2015/11/10 22:25:02 Got current settings
{"meterId":2,"seriesId":73,"communicationChannel":1,"risingEdgeAmounts":[0,1,2,3,4,5],"fallingEdgeAmounts":[0,1,2,3,4,5]}
2015/11/10 22:25:02 id=4294967295
2015/11/10 22:25:57 len= 27
2015/11/10 22:25:57 n=27
2015/11/10 22:25:57 Waiting for data
{"meterId":2,"seriesId":73,"communicationChannel":1,"risingEdgeAmounts":[127,93,117,149,169,153],"fallingEdgeAmounts":[33,15,17,38,41,48]}