/**
* Read the raw gyro values and display every 100th one
**/
func main() {
var (
err error
errCnt int
pause time.Duration
i int
x, y, z int16
xx, yy, zz int
px, py, pz int
gyroscope *sensors.L3GD20 = nil
)
gyroscope, err = sensors.NewL3GD20()
if err != nil {
fmt.Printf("Error: getting device L3GD20, err=%v\n", err)
} else {
pause = time.Millisecond * 100
for {
x, y, z, err = gyroscope.ReadRaw()
if err != nil {
errCnt++
} else {
i++
xx += int(x)
yy += int(y)
zz += int(z)
if i == 10 {
xx = xx / i
yy = yy / i
zz = zz / i
fmt.Printf("%4d, %4d, %4d\n", xx-px, yy-py, zz-pz)
i = 0
px = xx
py = yy
pz = zz
xx = 0
yy = 0
zz = 0
}
}
time.Sleep(pause)
}
}
}
/**
* Setup the sensors
**/
func setup() (gyroscope *sensors.L3GD20, accelerometer *sensors.LSM303ACCEL, magnetometer *sensors.LSM303MAG, err error) {
fmt.Printf("Setup...\n")
gyroscope, err = sensors.NewL3GD20()
if err != nil {
fmt.Printf("Error: getting device L3GD20, err=%v\n", err)
} else {
accelerometer, err = sensors.NewLSM303ACCEL()
if err != nil {
fmt.Printf("Error: getting device LSM303ACCEL, err=%v\n", err)
} else {
magnetometer, err = sensors.NewLSM303MAG()
if err != nil {
fmt.Printf("Error: getting device LSM303MAG, err=%v\n", err)
//} else {
// err = calibrate(gyroscope, accelerometer)
// if err != nil {
// fmt.Printf("Error: %v\n", err)
// }
}
}
}
return
}
/**
* This test program reads data from the three sensors
* gyroscope, accelerometer, and magnetometer, runs it
* through the filter, and prints the computed
* Yaw, Pitch, and Roll every 100 iterations.
* Each iteration takes approximately 3 milliseconds
* on a RaspberryPi model B.
**/
func main() {
const (
d2r = math.Pi / 180.0 // Used to convert degrees to radians
r2d = 180.0 / math.Pi // Used to convert radians to degrees
)
var (
gyroscope *sensors.L3GD20 = nil
accelerometer *sensors.LSM303ACCEL = nil
magnetometer *sensors.LSM303MAG = nil
imu *imus.ImuMayhony = nil
err error
dbgPrint bool
gx, gy, gz float32 // Gyroscope rate in degrees
ax, ay, az float32 // Accelerometer data
mx, my, mz float32 // Magnetometer data
yaw, pitch, roll float32 // IMU results in radians
)
gyroscope, err = sensors.NewL3GD20()
if err != nil {
fmt.Printf("Error: getting device L3GD20, err=%v\n", err)
return
}
accelerometer, err = sensors.NewLSM303ACCEL()
if err != nil {
fmt.Printf("Error: getting device LSM303ACCEL, err=%v\n", err)
return
}
magnetometer, err = sensors.NewLSM303MAG()
if err != nil {
fmt.Printf("Error: getting device LSM303MAG, err=%v\n", err)
return
}
imu = imus.NewImuMayhony()
maxIterations := 10000
for {
startTime := time.Now().UnixNano()
for i := 0; i < maxIterations; i++ {
dbgPrint = (i % 100) == 0
now := time.Now().UnixNano()
gx, gy, gz, err = gyroscope.ReadXYZ()
if err == nil {
ax, ay, az, err = accelerometer.ReadXYZ()
if err == nil {
mx, my, mz, err = magnetometer.ReadXYZ()
if err == nil {
yaw, pitch, roll = imu.Update(now, gx*d2r, gy*d2r, gz*d2r, ax, ay, az, mx, my, mz)
if dbgPrint {
fmt.Printf(" YPR(%10.5f, %10.5f, %10.5f)\n", yaw*r2d, pitch*r2d, roll*r2d)
}
} else {
fmt.Printf("Error: reading magnetometer, err=%v\n", err)
}
} else {
fmt.Printf("Error: reading accelerometer, err=%v\n", err)
}
} else {
fmt.Printf("Error: reading gyroscope, err=%v\n", err)
}
}
finishTime := time.Now().UnixNano()
delta := finishTime - startTime
fmt.Printf("%4.2f milliseconds per iteration\n", (float64(delta)/float64(maxIterations))/1000000.0)
}
}
