Ook-decoder reads On-Off Keying radio data commonly used in the 433MHz ISM bands using a software defined radio (SDR).

ON HOLD: My test rig is 500 miles away and unreachable during winter months. The transmitter has failed, so no more development until the spring thaw comes and I can get a human out there.

I'm just filling this repository now, you probably don't want to use it yet.

$ make
$ make install

On-Off-Keying (OOK) is a simple radio modulation scheme where the carrier is pulsed on and off to encode data. Morse code is a well known historical example. In modern times OOK is commonly used in the Industrial, Scientific, and Medical (ISM) radio bands (433MHz, 900MHz, and others) by simple telemetry devices like weather stations, remote thermometers, alarm systems, and other remote sensors.

These devices are generally cobbled together by embedded system electrical engineers who didn't study advanced encoding techniques, believe in simplicity, and are using the smallest, cheapest microcontroller possible. Typically short pulses and long pulses are used to encode ones and zeros in an arbitrary polarity. Sometimes distance between the pulses carries the data, or carries bits of its own. Generally there are one or more start pulses to let the receiver's automatic gain control (AGC) sort itself out before the data comes rolling in.

It seems unlikely to imagine a general solution to decode all of the protocols imagined by the engineers, to that end, this software is split into two layers.

ookd receives and analyzes the RF data looking for bursts of pulses. When it finds a pulse burst it multicasts the pulses to an arbitrary number of listens. ookd doesn't know anything about any specific protocol. Most of the computation takes place in ookd. In a typical environment ookd will receive and perform computation on 2MB/s and pass on less than 100B/s. You should not need to alter ookd to support a new device.

Decoding processes receive the multicast pulse bursts and attempt to decode them. For development simplicity it is envisioned that each type of device will have its own decoder process. A typical decoder would look at the length of the pulse stream, the length of individual pulses, and the plausibility of the data to decide if it has received a valid message from a device it understands. It can then take whatever action it wishes.

ookdump is a client which characterizes and dumps received bursts. You will find it useful for understanding your device's protocol and if you are lucky how to set the parameters to an already existing function to convert your pulse stream into an array of bytes.

wh1080 decodes weather information from Fine Offset wh1080/wh1081 based weather stations. These are sold under many brand names. Mine is an Ambient Weather. If you get a burst or two of 88 pulses every 45 seconds, you are probably a wh1080. This saves a json file with the current observations and also writes periodic files of accumulated data.

??? Add the LaCrosse reader here.

nexa decodes ON/OFF signals for Nexa wireless units (http://www.nexa.se) of the smart home. This outputs the transmitter code to stdout and can also send statistics to StatsD server.

The rtl-sdr library and the ook library itself are linked statically to avoid build complexity.

I build and test on Linux and Mac OS X. Others probably work. If you feel you must send me a Windows patch, make it very clean.

rtl-sdr uses the software defined radio in common USB TV receivers to capture raw RF data and deliver it to your process. Although I have licensed my code freely, this rtl-sdr is GPL2 and propagates its GPL2 requirements to my code if you distribute a binary. If that is a problem for you, then write your own rtl-sdr replacement.

If you would rather use a hardware 433MHz receiver you could dispense with the SDR section and multicast pulse data directly from your receiver's data line. All of the decoders would still work.

Either gcc or clang works fine. It also needs to support the non-standard ({ }) statement expression extension. (That see's limited use and you could patch around it easily if you need to.) Just be happy I refrained from using blocks in clang for the sake of gcc users.

On an original BeagleBone at 250ksps ookd will consume about 30% of the CPU. This is almost entirely because I am doing floating point math and I suspect it is all soft float because of my Debian variant. The clang code is faster than the gcc code with the compilers in Debian Wheezy.

In general, ookd matters for performance, but the clients don't. The data reduction between the two is just too large for the clients to matter.

You will need the rtl-sdr library to build. You can install this with:

$ brew install librtlsdr

If you have to build rtl-sdr, you will need to install a bunch of utilities. I made it build with:

$ sudo chmod 2775 /usr/local/include
$ brew install cmake
$ brew install pkgconfig
$ brew install libusb
$ mkdir build
$ cd build
$ cmake ..
$ make
$ make install

rtl-433 was helpful for getting started. It provides a great deal of analysis of the 433MHz signals.