Пример #1
0
// startListening on the network addresses
func startListening(ctx context.Context, host p2phost.Host, cfg *config.Config) error {
	listenAddrs, err := listenAddresses(cfg)
	if err != nil {
		return err
	}

	// make sure we error out if our config does not have addresses we can use
	log.Debugf("Config.Addresses.Swarm:%s", listenAddrs)
	filteredAddrs := addrutil.FilterUsableAddrs(listenAddrs)
	log.Debugf("Config.Addresses.Swarm:%s (filtered)", filteredAddrs)
	if len(filteredAddrs) < 1 {
		return fmt.Errorf("addresses in config not usable: %s", listenAddrs)
	}

	// Actually start listening:
	if err := host.Network().Listen(filteredAddrs...); err != nil {
		return err
	}

	// list out our addresses
	addrs, err := host.Network().InterfaceListenAddresses()
	if err != nil {
		return err
	}
	log.Infof("Swarm listening at: %s", addrs)
	return nil
}
Пример #2
0
// dial is the actual swarm's dial logic, gated by Dial.
func (s *Swarm) dial(ctx context.Context, p peer.ID) (*Conn, error) {
	var logdial = lgbl.Dial("swarm", s.LocalPeer(), p, nil, nil)
	if p == s.local {
		log.Event(ctx, "swarmDialDoDialSelf", logdial)
		return nil, ErrDialToSelf
	}
	defer log.EventBegin(ctx, "swarmDialDo", logdial).Done()
	logdial["dial"] = "failure" // start off with failure. set to "success" at the end.

	sk := s.peers.PrivKey(s.local)
	logdial["encrypted"] = (sk != nil) // log wether this will be an encrypted dial or not.
	if sk == nil {
		// fine for sk to be nil, just log.
		log.Debug("Dial not given PrivateKey, so WILL NOT SECURE conn.")
	}

	// get remote peer addrs
	remoteAddrs := s.peers.Addrs(p)
	// make sure we can use the addresses.
	remoteAddrs = addrutil.FilterUsableAddrs(remoteAddrs)
	// drop out any addrs that would just dial ourselves. use ListenAddresses
	// as that is a more authoritative view than localAddrs.
	ila, _ := s.InterfaceListenAddresses()
	remoteAddrs = addrutil.Subtract(remoteAddrs, ila)
	remoteAddrs = addrutil.Subtract(remoteAddrs, s.peers.Addrs(s.local))

	log.Debugf("%s swarm dialing %s -- local:%s remote:%s", s.local, p, s.ListenAddresses(), remoteAddrs)
	if len(remoteAddrs) == 0 {
		err := errors.New("peer has no addresses")
		logdial["error"] = err
		return nil, err
	}

	remoteAddrs = s.filterAddrs(remoteAddrs)
	if len(remoteAddrs) == 0 {
		err := errors.New("all adresses for peer have been filtered out")
		logdial["error"] = err
		return nil, err
	}

	// try to get a connection to any addr
	connC, err := s.dialAddrs(ctx, p, remoteAddrs)
	if err != nil {
		logdial["error"] = err
		return nil, err
	}
	logdial["netconn"] = lgbl.NetConn(connC)

	// ok try to setup the new connection.
	defer log.EventBegin(ctx, "swarmDialDoSetup", logdial, lgbl.NetConn(connC)).Done()
	swarmC, err := dialConnSetup(ctx, s, connC)
	if err != nil {
		logdial["error"] = err
		connC.Close() // close the connection. didn't work out :(
		return nil, err
	}

	logdial["dial"] = "success"
	return swarmC, nil
}
Пример #3
0
func filterAddrs(listenAddrs []ma.Multiaddr) ([]ma.Multiaddr, error) {
	if len(listenAddrs) > 0 {
		filtered := addrutil.FilterUsableAddrs(listenAddrs)
		if len(filtered) < 1 {
			return nil, fmt.Errorf("swarm cannot use any addr in: %s", listenAddrs)
		}
		listenAddrs = filtered
	}
	return listenAddrs, nil
}